双极性晶体管

二极管

ESD保护、TVS、滤波和信号调节ESD保护

MOSFET

氮化镓场效应晶体管(GaN FET)

绝缘栅双极晶体管(IGBTs)

模拟和逻辑IC

汽车应用认证产品(AEC-Q100/Q101)

NCA9306DC-Q100

2-bit bidirectional multi-voltage level translator; open-drain; push-pull

The NCA9306-Q100 is a 2 channel bidirectional I²C and SMBus multi-voltage level translator with an enable (EN) pin input. It allows voltage translation between 0.95 V and 5 V without the use of a direction pin. It supports up to 100 MHz up translation and >100 MHz down translation at ≤ 30 pF capacitive load. There is no need for a direction pin which minimizes the system effort. The NCA9306-Q100 supports 5 V tolerant I/O pins to support mixed mode signal operation. The ability to set up different voltage translation levels on each channel makes the device very flexible and suitable for a lot of different applications.

The low ON-state resistance RON of the switch allows connections to be made with minimal propagation delay. When EN is HIGH, the translator switch is on, and the SCLA and SDAA I/O are connected to the SCLB and SDAB I/O respectively, allowing bidirectional data flow between ports. When EN is LOW, the translator switch is off, and a high-impedance state exists between ports. As with the standard I²C bus-system, pull-up resistors are required to provide the logic HIGH levels on the translators bus. The NCA9306-Q100 has a standard open-drain configuration of the I²C-bus. The size of these pull-up resistors depend on the system. Each side of the translator must have a pull-up resistors. NCA9306-Q100 is designed to work with Standard-mode, Fast-mode and Fast-mode plus I²C bus devices in addition to the SMBus devices.

When the SDAA or SDAB pin is LOW, the clamp is in the ON-state and a low resistance connections exists between the SDAA and SDAB ports. Assuming the higher voltage is on the SDAB port when the SDAB port is HIGH, the voltage on the SDAA port is limited to the voltage set by refA. When the SDAA port is HIGH, the SDAB port is pulled to the refB supply voltage by the pull-up resistors. The SCLA or SCLB pins also follows the same behavior as described for SDAA or SDAB pins.

This product has been qualified to the Automotive Electronics Council (AEC) standard Q100 (Grade 1) and is suitable for use in automotive applications.

Features and benefits

  • Automotive product qualification in accordance with AEC-Q100 (Grade 1)

    • Specified from -40 °C to +125 °C

  • 2-channel bidirectional voltage translator for SDA and SCL lines in mixed mode I²C bus applications

  • Open-drain I²C-bus I/O ports (SCLA, SDAA, SCLB and SDAB)

  • Provides bidirectional voltage translation with no direction pin

  • High-impedance SCLA, SDAA, SCLB and SDAB for EN = LOW

  • Up translation

    • < 100 MHz; CL = 30 pF

    • < 40 MHz; CL = 50 pF

  • Down translation

    • > 100 MHz; CL = 30 pF

    • < 40 MHz; CL = 50 pF

  • Hot insertion

  • Bidirectional voltage level translation between:

    • 0.95 V and 1.8 V, 2.5 V, 3.3 V and 5.0 V

    • 1.2 V and 1.8 V, 2.5 V, 3.3 V and 5.0 V

    • 1.8 V and 2.5 V, 3.3 V and 5.0 V

    • 2.5 V and 3.3 V and 5.0 V

    • 3.3 V and 5.0 V

  • Low standby current

  • 5 V tolerant I²C-bus I/O pins to support mixed mode signal operation

  • Low RON provides less signal distortion

  • Latch-up performance exceeds 100 mA per JESD78 class II level A

  • ESD protection:

    • HBM ANSI/ESDA/JEDEC JS-001 class 2 exceeds 2000 V

    • CDM ANSI/ESDA/JEDEC JS-002 class C3 exceeds 1000 V

Applications

  • GPIO, MDIO, PMBus, SMBus, SDIO, UART, I²C, and other interfaces in Telecom infrastructure

  • Industrial

  • Personal computing

  • Router and Industrial Automation

参数类型

型号 VCC(A) (V) VCC(B) (V) Logic switching levels Output drive capability (mA) tpd (ns) Nr of bits Power dissipation considerations Tamb (°C) Package name
NCA9306DC-Q100 0.95 - 5.0 0.95 - 5.0 CMOS + 64 0.4 2 low -40~125 VSSOP8

封装

型号 可订购的器件编号,(订购码(12NC)) 状态 标示 封装 外形图 回流焊/波峰焊 包装
NCA9306DC-Q100 NCA9306DC-Q100H
(935691282125)
Active h9 SOT765-1
VSSOP8
(SOT765-1)
SOT765-1 SOT765-1_125

环境信息

型号 可订购的器件编号 化学成分 RoHS RHF指示符
NCA9306DC-Q100 NCA9306DC-Q100H NCA9306DC-Q100 rohs rhf rhf
品质及可靠性免责声明

文档 (9)

文件名称 标题 类型 日期
NCA9306_Q100 2-bit bidirectional multi-voltage level translator; open-drain; push-pull Data sheet 2024-08-05
Nexperia_document_guide_MiniLogic_PicoGate_201901 PicoGate leaded logic portfolio guide Brochure 2019-01-07
SOT765-1 3D model for products with SOT765-1 package Design support 2020-01-22
nca9306 NCA9306 IBIS model IBIS model 2020-09-23
Nexperia_package_poster Nexperia package poster Leaflet 2020-05-15
VSSOP8_SOT765-1_mk plastic, very thin shrink small outline package; 8 leads; 0.5 mm pitch; 2 mm x 2.3 mm x 1 mm body Marcom graphics 2017-01-28
SOT765-1 plastic, very thin shrink small outline package; 8 leads; 0.5 mm pitch; 2 mm x 2.3 mm x 1 mm body Package information 2022-06-03
SOT765-1_125 VSSOP8; Reel pack for SMD, 7''; Q3/T4 product orientation Packing information 2020-04-21
NCA9306DC-Q100_Nexperia_Product_Reliability NCA9306DC-Q100 Nexperia Product Reliability Quality document 2024-06-16

支持

如果您需要设计/技术支持,请告知我们并填写 应答表 我们会尽快回复您。

模型

文件名称 标题 类型 日期
nca9306 NCA9306 IBIS model IBIS model 2020-09-23
SOT765-1 3D model for products with SOT765-1 package Design support 2020-01-22

订购、定价与供货

型号 Orderable part number Ordering code (12NC) 状态 包装 Packing Quantity 在线购买
NCA9306DC-Q100 NCA9306DC-Q100H 935691282125 Active SOT765-1_125 3,000 订单产品

样品

作为 Nexperia 的客户,您可以通过我们的销售机构订购样品。

如果您没有 Nexperia 的直接账户,我们的全球和地区分销商网络可为您提供 Nexperia 样品支持。查看官方经销商列表

How does it work?

The interactive datasheets are based on the Nexperia MOSFET precision electrothermal models. With our interactive datasheets you can simply specify your own conditions interactively. Start by changing the values of the conditions. You can do this by using the sliders in the condition fields. By dragging the sliders you will see how the MOSFET will perform at the new conditions set.

可订购部件

型号 可订购的器件编号 订购代码(12NC) 封装 从经销商处购买
NCA9306DC-Q100 NCA9306DC-Q100H 935691282125 SOT765-1 订单产品