双极性晶体管

二极管

ESD保护、TVS、滤波和信号调节ESD保护

MOSFET

氮化镓场效应晶体管(GaN FET)

绝缘栅双极晶体管(IGBTs)

模拟和逻辑IC

汽车应用认证产品(AEC-Q100/Q101)

74AVCH16244DGG

16-bit buffer/line driver; 3.6 V tolerant; 3-state

The 74AVCH16244 is a 16-bit non-inverting buffer/line driver with 3-state outputs. The device can be used as four 4-bit buffers, two 8-bit buffers or one 16-bit buffer. The 3‑state outputs are controlled by the output enable inputs nOE. A HIGH on nOE causes the outputs to assume a high impedance OFF-state.

The 74AVCH16244 is designed to have an extremely fast propagation delay and a minimum amount of power consumption.

To ensure the high-impedance output state during power-up or power-down, nOE should be tied to VCC through a pull-up resistor (Live Insertion).

A dynamic controlled output (DCO) circuitry is implemented to support termination line drive during transient.

The 74AVCH16244 has active bus-hold circuitry to hold unused or floating data inputs at a valid logic level. This feature eliminates the need for external pull-up or pull-down resistors.

This product has been discontinued

Features and benefits

  • Wide supply voltage range from 1.2 V to 3.6 V

  • CMOS low power consumption

  • Low inductance multiple VCC and GND pins for minimum noise and ground bounce

  • Input/output tolerant up to 3.6 V

  • Dynamic controlled output (DCO) circuit dynamically changes the output impedance, resulting in noise reduction without speed degradation

  • Bus hold on all data inputs

  • Supports Live Insertion

  • Complies with JEDEC standards:

    • JESD8-7 (1.2 V to 1.95 V)

    • JESD8-5 (1.8 V to 2.7 V)

    • JESD8-1A (2.7 V to 3.6 V)

Applications

Parametrics

Type number Package name
74AVCH16244DGG TSSOP48

PCB Symbol, Footprint and 3D Model

Model Name Description

Package

All type numbers in the table below are discontinued.

Type number Orderable part number, (Ordering code (12NC)) Status Marking Package Package information Reflow-/Wave soldering Packing
74AVCH16244DGG 74AVCH16244DGG,112
(935266778112)
Obsolete AVCH16244 Standard Procedure Standard Procedure SOT362-1
TSSOP48
(SOT362-1)
SOT362-1 SSOP-TSSOP-VSO-WAVE
Not available
74AVCH16244DGG,118
(935266778118)
Obsolete AVCH16244 Standard Procedure Standard Procedure SOT362-1_118
74AVCH16244DGG,512
(935266778512)
Obsolete AVCH16244 Standard Procedure Standard Procedure Not available
74AVCH16244DGG,518
(935266778518)
Obsolete AVCH16244 Standard Procedure Standard Procedure Not available

Environmental information

All type numbers in the table below are discontinued.

Type number Orderable part number Chemical content RoHS RHF-indicator
74AVCH16244DGG 74AVCH16244DGG,112 74AVCH16244DGG rohs rhf rhf
74AVCH16244DGG 74AVCH16244DGG,118 74AVCH16244DGG rohs rhf rhf
74AVCH16244DGG 74AVCH16244DGG,512 74AVCH16244DGG rohs rhf rhf
74AVCH16244DGG 74AVCH16244DGG,518 74AVCH16244DGG rohs rhf rhf
Quality and reliability disclaimer

Documentation (7)

File name Title Type Date
74AVCH16244 16-bit buffer/line driver; 3.6 V tolerant; 3-state Data sheet 2018-02-20
AN90007 Pin FMEA for AVC family Application note 2018-11-30
SOT362-1 3D model for products with SOT362-1 package Design support 2020-01-22
Nexperia_package_poster Nexperia package poster Leaflet 2020-05-15
TSSOP48_SOT362-1_mk plastic, thin shrink small outline package; 48 leads; 0.5 mm pitch; 12.8 mm x 6.1 mm x 1.2 mm body Marcom graphics 2017-01-28
SOT362-1 plastic thin shrink small outline package; 48 leads; body width 6.1 mm Package information 2024-01-05
SSOP-TSSOP-VSO-WAVE Footprint for wave soldering Wave soldering 2009-10-08

Support

If you are in need of design/technical support, let us know and fill in the answer form we'll get back to you shortly.

Models

File name Title Type Date
SOT362-1 3D model for products with SOT362-1 package Design support 2020-01-22

PCB Symbol, Footprint and 3D Model

Model Name Description

How does it work?

The interactive datasheets are based on the Nexperia MOSFET precision electrothermal models. With our interactive datasheets you can simply specify your own conditions interactively. Start by changing the values of the conditions. You can do this by using the sliders in the condition fields. By dragging the sliders you will see how the MOSFET will perform at the new conditions set.